[koyup]

Раз уж залез в эту тему, вот что написано в книжке PERIODIC INSPECTION AND MAINTENANCE
Для двигателя 3л с АТ, для 2,4 с вариатором похоже так-же, только там 6л вариаторной жидкости, и вытекать будет меньше.
Хоть и говорят салонные засланцы про кривые ручки: 30 мин и можно Severe юзать.
Change automatic transmission fluid:
Normal usageEvery 90,000 km or every 6 years
Severe usageEvery 45,000 km or every 3 years
Нормальное использование 90 000 км или каждые 6 лет
Серьезное использование 45 000 км или каждые 3 года
Вольный перевод:
После пробега 45-90т.км (кто как ездит)Покупаешь в Экзисите нужную жидкость DIA QUEEN CVTF-J1, на прогретой машинке ,откручиваешь шланг, по которому течет ATFот трансмиссии к радиатору , заводишь двиг на «N», сливаешь 3,5л, глушишь ч/з 1 минуту,откр. Сливную пробку, вытечет 2л, итого 5,5л,
Закруч пробку, наливаешь с-ко вытекло (5,5л), опять заводишь на 1 мин и сливаешь ч/з шланг 3,5л, доливаешь 3,5л.
Если жидкость грязновата, повторяем последний шаг. Прогреваем, проверяем щупом.Наслаждаемся.

E2. CHANGE AUTOMATICTRANSMISSION FLUID

M6020600200157
SPECIFICATIONSCHANGE PROCEDURE
If you have an ATF changer, use the ATF changer to flush the ATF. If you do not have an ATF changer, fol-low the procedure given below.
1. Remove the hose shown in the illustration which allows the ATF to flow from the ATF cooler (built into the radiator) to the transmission. 2. Start the engine and discharge the ATF.

Driving conditions: N range, idling

The engine should be stopped within one minute of it being started. If the ATF has all been discharged before this, stop the engine at that point.
Discharge amount: Approx. 3.5 L
3. Remove the drain plug at the bottom of the transmission case to drain out the remaining ATF.Discharge amount: Approx. 2.0 L
4. Install the drain plug with a gasket in between, and tighten it to the specified torque.Tightening torque: 32 ± 2 N⋅m
5. Pour in new ATF through the oil filler tube.
Amount to add: Approx. 5.5 L
CAUTION
Stop pouring in the ATF once 5.5 L has been poured in.
6. Repeat the operation in step 2.
7. Pour in new ATF through the oil filler tube.
Amount to add: Approx. 3.5 L
NOTE: Carry out steps 2 and 7 so that at least 8.0 L has been discharged from the cooler hose. After this, discharge a small quantity of ATF and check for contamination. If the ATF is contaminated, repeat steps 6 and 7.
8. Connect the hose which was disconnected in step 1, and then securely re-insert the oil level gauge. 9. Start the engine, and let it run at idle for 1 − 2 minutes.
10.Move the selector lever to all positions once, and then return it to the N position.
11.Check that the ATF level on the oil level gauge is at the COLD mark. If it is not up to this mark, add more ATF.
12.Drive the vehicle until the ATF temperature reaches the normal temperature (70 − 80°C), and then re-check the ATF level.
The ATF level must be between the HOT marks.
NOTE: .
1. The COLD mark is for reference only; the HOT marks should be used as the standard for judgment.
2. Measure ATF temperature using M.U.T.-II/III.
3. Check the oil level referring to the characteristics chart if it takes some time until reaching the normal operation temperature of ATF (70 − 80 °C.)
13.When ATF is under the specified level, top up ATF. When ATF is over the specified level, drain the excessive ATF from the drain plug to adjust ATF level to the specified level.
14.Securely insert the oil level gauge into the oil filler tube.